To measure ring size at home, measure the inside diameter of a ring that already fits you, in millimeters, and look it up in the chart below. A 17.3 mm diameter is a US size 7, for example. No ring to hand? Wrap a strip of paper around your finger, mark where it overlaps, and measure that length. That’s your finger’s circumference: 54.4 mm is also a US 7.

A calibrated ruler on your phone makes either method quick, because you can read millimeters directly on the screen. The whole thing takes about two minutes.

Which method should you use?

Method What you need Accuracy Best for
1. Measure a ring that fits A ring + phone ruler ± ¼ size Most people, surprise gifts
2. Paper strip Paper, pen + ruler ± ½ size No ring to copy
3. Trace a ring Paper, pencil + ruler ± ½ size Thick or chunky rings
Jeweler’s ring sizer A visit to a jeweler Exact Engagement and expensive rings

Method 1: Measure a ring that fits (most accurate)

  1. Calibrate the ruler. Open ruleronphone, choose Card, and match a credit card’s 85.60 mm edge. (How to calibrate.)
  2. Lay the ring flat on the screen, close to the ruler edge.
  3. Measure the inside edge to inside edge across the widest part. Don’t include the metal band.
  4. Measure twice, turning the ring 90°. Old rings can be slightly oval. Use the larger number.
  5. Find the diameter in the chart below.

Use a ring that fits the same finger you’re buying for. Fingers on your dominant hand are often slightly larger.

Using the selection tool: on the ruler, drag a selection box across the inside of the ring. It shows the width in mm directly, so you don’t have to count ticks.

Method 2: Paper strip or string

  1. Cut a thin strip of paper about 10 cm long and 5 mm wide (string stretches, so paper is better).
  2. Wrap it snugly around the base of your finger, not too tight.
  3. Mark where the paper overlaps with a pen.
  4. Lay it flat and measure from the end to the mark in mm. That’s your circumference.
  5. Look up the circumference in the chart.

Check the knuckle: if your knuckle is larger than the base of your finger, measure both and use the size between them, so the ring can slide on.

Worked example: your strip measures 56 mm. In the chart, that’s between US 7.5 (55.7 mm) and 8 (57.0 mm). Your knuckle measures 58 mm. Choose US 8, so the ring passes the knuckle.

Method 3: Draw the inside of a ring

If the ring is too thick to lay flat, place it on paper and trace the inside with a sharp pencil held straight up. Then measure the diameter of the circle in two directions and take the average. This is less precise than Method 1. Expect up to half a size of error, because the pencil line has width.

Ring size chart (inside diameter and circumference)

US and Canadian sizes follow a fixed step: each full size adds 0.8128 mm (0.032 in) to the inside diameter. Diameters below use the common formula diameter (mm) = 11.63 + 0.8128 × US size, rounded to 0.1 mm. Circumference = diameter × π.

US / Canada Diameter (mm) Circumference (mm) UK / Australia EU / ISO 8653
3 14.1 44.2 F½ 44
3½ 14.5 45.5 45.5
4 14.9 46.8 H½ 47
4½ 15.3 48.0 48
5 15.7 49.3 J½ 49
5½ 16.1 50.6 50.5
6 16.5 51.9 L½ 52
6½ 16.9 53.1 53
7 17.3 54.4 N½ 54
7½ 17.7 55.7 55.5
8 18.1 57.0 P½ 57
8½ 18.5 58.2 58
9 18.9 59.5 R½ 59.5
9½ 19.4 60.8 61
10 19.8 62.1 T½ 62
10½ 20.2 63.3 63.5
11 20.6 64.6 V½ 64.5
11½ 21.0 65.9 66
12 21.4 67.2 Y 67
12½ 21.8 68.5 68.5
13 22.2 69.7 Z+1 70

Each US size is about 0.81 mm larger in diameter (or 2.55 mm in circumference) than the size below it. Half sizes sit exactly in between. EU sizes follow ISO 8653 and are simply the inside circumference in millimeters, rounded. UK sizes use letters, with roughly one letter per half US size; the UK column above gives the equivalent for each whole US size.

Different jewelers’ charts can differ by about 0.1 mm, because they round differently. That’s far less than half a size, so any of them will give you the same answer.

How tight should a ring fit?

  • Right fit: it slides over the knuckle with slight resistance and doesn’t spin around on its own.
  • Too tight: it leaves a deep mark or you need soap to get it off.
  • Too loose: it falls off when your hands are cold or wet, or the stone turns to the palm side.

Adjust for band width

Wider bands touch more of your finger, so they feel tighter at the same size.

Band width Adjustment
Up to 4 mm Your measured size
4–6 mm Consider +¼ size
6–8 mm +½ size
Over 8 mm +½ to +1 size; try one on if you can

Comfort-fit bands have a rounded inside, which can feel a quarter size looser. Ask the seller how their comfort fit runs.

Why “actual size” ring charts often fail

Printable ring size charts only work if they print at exactly 100%. Most printers default to “fit to page,” which shrinks everything by 3–6%. That’s enough to make a size 7 look like a 6½. Always check a printout with a credit card (85.60 mm). Or skip the printer and use a calibrated actual size ruler on your screen, which you can verify the same way. If your screen ruler seems off, see why online rulers are inaccurate.

Tips for getting the right ring size

  • Measure at the end of the day. Fingers are smallest in the morning and in the cold, and largest when warm. Avoid measuring right after exercise or a hot shower.
  • Measure 3–4 times and take the most common result.
  • Wide bands (over 6 mm) fit tighter. Go up half a size.
  • Buying a surprise gift? Borrow a ring they wear on the same finger and use Method 1. It’s the most accurate way. If it’s from a different finger, adjust: ring fingers and middle fingers differ by about half to one size.
  • Between two sizes? Choose the larger one. A slightly loose ring can be fitted with a sizing bead; a tight one can’t be worn.
  • Check before you buy: some materials, like tungsten carbide, ceramic and many titanium rings, can’t be resized. Get the size right first time, or confirm the seller’s exchange policy.
  • For an engagement ring or an expensive piece, confirm the size with a jeweler’s sizer. Home methods are great for estimates and fashion rings.

New to reading millimeters? See how to read a ruler in mm, or convert sizes with the mm to inches chart. Ring sizes in inches: a US 7 is 0.682 in inside diameter.

How to calculate ring size from mm

If your measurement falls between chart rows, or you want the exact number, you can work out the US size from the same formula the chart uses.

  • From inside diameter: US size = (diameter in mm − 11.63) ÷ 0.8128
  • From circumference: first divide by π (3.1416) to get the diameter, then use the line above.
  • EU / ISO 8653 size: the inside circumference in mm, so a 54 mm circumference is EU 54.

Worked example (diameter): a ring measures 18.5 mm inside. (18.5 − 11.63) ÷ 0.8128 = 6.87 ÷ 0.8128 ≈ 8.45, which rounds to US 8½.

Worked example (circumference): your paper strip measures 52 mm. 52 ÷ 3.1416 ≈ 16.55 mm diameter. (16.55 − 11.63) ÷ 0.8128 ≈ 6.05, so US 6, and EU 52.

Round to the nearest quarter or half size. If the result lands close to halfway, use the larger size, for the knuckle reasons above.

Ring size in inches

US sizes were originally defined in inches: size 0 has an inside diameter of 0.458 in, and each whole size adds 0.032 in. If you measure in inches, use this table (diameter in inches = mm ÷ 25.4).

US size Inside diameter (in) Inside diameter (mm)
5 0.618 15.7
6 0.650 16.5
7 0.682 17.3
8 0.714 18.1
9 0.746 18.9
10 0.778 19.8
11 0.810 20.6
12 0.842 21.4

The steps are small: one whole size is just 1/32 inch of diameter. That’s why an inch ruler marked only in sixteenths is too coarse for ring sizing. Use the millimeter side, or a calibrated phone ruler set to mm.

How to measure ring size with string

String is the method most people try first, and it works if you avoid the two usual problems: it stretches, and it’s hard to mark.

  1. Use thin, non-stretchy string or dental floss, not yarn or elastic.
  2. Wrap it once around the base of the finger, snug but not cutting in.
  3. Pinch the crossing point and mark it with a fine pen while it’s still on your finger.
  4. Lay the string straight along the ruler without pulling it, and read the length in mm.
  5. Repeat three times. If the readings differ by more than 1 mm, your wrap was uneven.

A paper strip is still more reliable, because it can’t stretch and it lies flat for reading.

How to measure ring size for men

The method is identical; only the typical range is different. Men’s bands are also more often wide (6 mm and over), flat-profile, or made from tungsten, ceramic or titanium, which usually can’t be resized. That makes three things matter more:

  • Measure the knuckle as well as the base of the finger, since men’s knuckles are often noticeably larger than the base.
  • Apply the band width adjustment above. An 8 mm band at your measured size will often feel tight.
  • If you’re between sizes on a non-resizable band, go up rather than down.

How to measure a thumb, pinky or toe ring

  • Thumb rings: the thumb’s knuckle is usually much wider than its base. Measure both and choose a size close to the knuckle, or pick an open-back adjustable band.
  • Pinky rings: pinkies are small and the difference between sizes feels larger. Use Method 1 with an existing pinky ring if you can.
  • Toe rings: most are adjustable, so measuring is mainly to check the range. Measure where the ring will sit, below the toe’s joint.

Common ring sizing mistakes

  1. Measuring the outside of a ring. The band thickness can add 2–4 mm and several sizes. Always measure inside edge to inside edge.
  2. Measuring a ring from a different finger. Ring sizes can differ by up to a whole size between fingers on the same hand.
  3. Wrapping the paper too tight. If the paper dents the skin, the ring will be too small.
  4. Ignoring the knuckle. A ring that fits the base of the finger but won’t pass the knuckle is useless.
  5. Using an uncalibrated screen or a “fit to page” printout. A 3% scaling error is close to half a size.
  6. Measuring when your hands are cold. You’ll get a size that pinches on a warm day.
  7. Reading diameter where the chart wants circumference (or the reverse). A 17 mm figure is a US 6½ diameter but would be a tiny circumference; check which column you’re reading.

Troubleshooting

  • My two methods give different sizes. Trust the ring-diameter method (Method 1) over the paper strip, as long as the ring fits comfortably.
  • I’m exactly between sizes. Choose the larger size, or a quarter size up if the jeweler offers quarter sizes.
  • My knuckle is much bigger than my finger. A ring sized for the knuckle may spin. Ask about sizing beads or a spring insert, which narrow the inside after the ring is on.
  • My finger size changes a lot. That’s normal with temperature, pregnancy, and conditions like arthritis. Measure on several days and take the middle result, and talk to a jeweler about hinged or adjustable shanks if it varies a lot.
  • The phone ruler reading looks wrong. Recalibrate on the calibration page and check that browser zoom is at 100%.

Sources

  • ISO 8653: Jewellery — Ring-sizes — Definition, measurement and designation.
  • US ring sizing standard step of 0.032 in (0.8128 mm) diameter per size, as used in jeweler’s mandrels.
  • British Standard BS 6820 (UK alphabetical ring sizes).