There are exactly 25.4 millimeters in an inch (and 2.54 cm). That’s an international definition, not a rounded number. To convert, multiply inches by 25.4 to get mm, or divide mm by 25.4 to get inches. For example, 10 mm = 0.394 in and 1/4 in = 6.35 mm. The charts below cover every fraction to 1/32 inch and common metric sizes. If you want to see how big 1 cm or 1 inch is, an actual size ruler on your phone shows both side by side.

Quick conversion rules

From → to Do this Example
mm → inches ÷ 25.4 (or × 0.03937) 50 mm ÷ 25.4 = 1.969 in
inches → mm × 25.4 3 in × 25.4 = 76.2 mm
cm → inches ÷ 2.54 (or × 0.3937) 30 cm ÷ 2.54 = 11.81 in
inches → cm × 2.54 12 in × 2.54 = 30.48 cm
feet → cm × 30.48 6 ft × 30.48 = 182.88 cm

Mental shortcuts: 4 inches ≈ 10 cm (exactly 10.16 cm). 1 mm ≈ 1/25 inch. 1 meter ≈ 39.37 inches, a bit more than a yard.

Inches to mm chart (fractions to 1/32)

Rounded to two decimal places. Exact values: multiply the decimal by 25.4.

Inches Decimal Millimeters Centimeters
1/32 0.03125 0.79 0.08
1/16 0.0625 1.59 0.16
3/32 0.09375 2.38 0.24
1/8 0.125 3.18 0.32
5/32 0.15625 3.97 0.40
3/16 0.1875 4.76 0.48
7/32 0.21875 5.56 0.56
1/4 0.25 6.35 0.64
9/32 0.28125 7.14 0.71
5/16 0.3125 7.94 0.79
11/32 0.34375 8.73 0.87
3/8 0.375 9.53 0.95
13/32 0.40625 10.32 1.03
7/16 0.4375 11.11 1.11
15/32 0.46875 11.91 1.19
1/2 0.5 12.70 1.27
17/32 0.53125 13.49 1.35
9/16 0.5625 14.29 1.43
19/32 0.59375 15.08 1.51
5/8 0.625 15.88 1.59
21/32 0.65625 16.67 1.67
11/16 0.6875 17.46 1.75
23/32 0.71875 18.26 1.83
3/4 0.75 19.05 1.91
25/32 0.78125 19.84 1.98
13/16 0.8125 20.64 2.06
27/32 0.84375 21.43 2.14
7/8 0.875 22.23 2.22
29/32 0.90625 23.02 2.30
15/16 0.9375 23.81 2.38
31/32 0.96875 24.61 2.46
1 1.0 25.40 2.54

Whole inches to mm and cm

Inches Millimeters Centimeters
1 in 25.4 mm 2.54 cm
2 in 50.8 mm 5.08 cm
3 in 76.2 mm 7.62 cm
4 in 101.6 mm 10.16 cm
5 in 127.0 mm 12.70 cm
6 in 152.4 mm 15.24 cm
7 in 177.8 mm 17.78 cm
8 in 203.2 mm 20.32 cm
9 in 228.6 mm 22.86 cm
10 in 254.0 mm 25.40 cm
11 in 279.4 mm 27.94 cm
12 in (1 ft) 304.8 mm 30.48 cm
18 in 457.2 mm 45.72 cm
24 in (2 ft) 609.6 mm 60.96 cm
36 in (1 yd) 914.4 mm 91.44 cm

These are exact, because the inch is defined as 25.4 mm.

mm to inches chart

The nearest fraction is rounded to the closest 1/64 inch, which is how fine most imperial rulers and tape measures go.

Millimeters Inches (decimal) Nearest fraction
1 mm 0.0394 ≈ 3/64
2 mm 0.0787 ≈ 5/64
3 mm 0.1181 ≈ 1/8
4 mm 0.1575 ≈ 5/32
5 mm 0.1969 ≈ 13/64
6 mm 0.2362 ≈ 15/64
7 mm 0.2756 ≈ 9/32
8 mm 0.3150 ≈ 5/16
9 mm 0.3543 ≈ 23/64
10 mm (1 cm) 0.3937 ≈ 25/64
11 mm 0.4331 ≈ 7/16
12 mm 0.4724 ≈ 15/32
13 mm 0.5118 ≈ 33/64
14 mm 0.5512 ≈ 35/64
15 mm 0.5906 ≈ 19/32
16 mm 0.6299 ≈ 5/8
17 mm 0.6693 ≈ 43/64
18 mm 0.7087 ≈ 45/64
19 mm 0.7480 ≈ 3/4
20 mm (2 cm) 0.7874 ≈ 25/32
21 mm 0.8268 ≈ 53/64
22 mm 0.8661 ≈ 55/64
23 mm 0.9055 ≈ 29/32
24 mm 0.9449 ≈ 15/16
25 mm 0.9843 ≈ 63/64
30 mm (3 cm) 1.1811 ≈ 1 3/16
40 mm (4 cm) 1.5748 ≈ 1 37/64
50 mm (5 cm) 1.9685 ≈ 1 31/32
75 mm 2.9528 ≈ 2 61/64
100 mm (10 cm) 3.9370 ≈ 3 15/16
150 mm (15 cm) 5.9055 ≈ 5 29/32
200 mm (20 cm) 7.8740 ≈ 7 7/8
300 mm (30 cm) 11.8110 ≈ 11 13/16

cm to inches chart

Centimeters Inches Centimeters Inches
1 cm 0.394 in 16 cm 6.299 in
2 cm 0.787 in 17 cm 6.693 in
3 cm 1.181 in 18 cm 7.087 in
4 cm 1.575 in 19 cm 7.480 in
5 cm 1.969 in 20 cm 7.874 in
6 cm 2.362 in 25 cm 9.843 in
7 cm 2.756 in 30 cm 11.811 in
8 cm 3.150 in 40 cm 15.748 in
9 cm 3.543 in 50 cm 19.685 in
10 cm 3.937 in 60 cm 23.622 in
11 cm 4.331 in 70 cm 27.559 in
12 cm 4.724 in 80 cm 31.496 in
13 cm 5.118 in 90 cm 35.433 in
14 cm 5.512 in 100 cm 39.370 in
15 cm 5.906 in 150 cm 59.055 in

How to convert mm to a fraction of an inch

Tape measures and many tools use fractions, not decimals. To turn millimeters into the nearest fraction:

  1. Divide by 25.4 to get decimal inches. Example: 22 mm ÷ 25.4 = 0.866 in.
  2. Split off the whole inches. Here there are none, so you keep 0.866.
  3. Multiply the remainder by 16 (or 32, or 64, depending on how fine you need it). 0.866 × 16 = 13.86.
  4. Round to the nearest whole number and put it over 16: 14/16, which reduces to 7/8 in.

7/8 inch is 22.23 mm, so this rounding is 0.23 mm off. Use 32nds or 64ths for a closer match (0.866 × 64 = 55.4 → 55/64 in, only 0.17 mm off).

How big is 1 mm?

1 mm ≈ 0.04 inches, about the thickness of a credit card (0.76 mm) plus a bit, or of ten sheets of standard office paper. On a metric ruler it is the smallest gap between two lines.

How big is 1 cm?

1 cm = 10 mm ≈ 0.39 inches, a bit more than 3/8 inch. Everyday things that are about 1 cm:

  • The width of the fingernail on your little finger (varies by person)
  • The diameter of a standard AAA battery (10.5 mm)
  • The thickness of a typical smartphone (≈ 0.8 cm)
  • A standard pencil is a little under 1 cm wide (≈ 7–8 mm)

How big is 1 inch actual size?

1 inch = 25.4 mm = 2.54 cm. Everyday comparisons:

  • A US quarter is 24.26 mm, very close to 1 inch across
  • A standard AA battery is 14.5 mm wide, so a bit over half an inch
  • The top joint of an adult thumb is roughly an inch (varies a lot)
  • A credit card’s short edge is 2.125 inches, a little over two inches

To see an exact inch, open the online ruler and calibrate it with a credit card. Your screen then shows a true 1 inch at actual size, with millimeters alongside. The calibration page walks through it in under a minute. For more objects of known size, see how to measure without a ruler.

Why an inch is exactly 25.4 mm

Before 1959 the US and UK inch differed by a few parts per million. In 1959 the US, UK, Canada, Australia, New Zealand and South Africa agreed on an international yard of exactly 0.9144 meters, which makes the inch exactly 25.4 mm. The older “US survey foot” stayed in use for land surveying until NIST retired it at the end of 2022. For everyday measuring, there is only one inch: 25.4 mm.

Common rounding mistakes

  • Using 25 instead of 25.4. It’s 1.6% off: a 300 mm shelf becomes 12 in instead of 11.81 in.
  • Using 2.5 cm per inch. Same 1.6% error. Over a 2 m (78.7 in) curtain, that’s more than an inch.
  • Rounding too early. Convert first, then round once at the end.
  • Mixing up the direction. If the number gets bigger when you convert to inches, you multiplied instead of dividing.

Which unit should you measure in?

For small things like jewelry, screws, beads and electronics, millimeters are more precise and easier to read than sixteenths of an inch. For anything you’ll buy or share in the US, note the inches too. A ruler that shows both at once avoids conversion errors altogether. Learn to read both scales in how to read a ruler, and check paper and card sizes in the A4 size chart and credit card size guide.

Quick answers to the most-searched conversions

These are the single conversions people look up most often. Fractions are exact; metric-to-inch values are rounded to three decimals.

Question Answer
How many mm is 1/8 inch? 3.175 mm
How many mm is 1/4 inch? 6.35 mm
How many mm is 3/8 inch? 9.525 mm
How many mm is 1/2 inch? 12.7 mm
How many mm is 3/4 inch? 19.05 mm
How many mm is 1 1/8 inches? 28.575 mm
How many mm is 1 1/4 inches? 31.75 mm
How many mm is 2 inches? 50.8 mm
How many mm is 2.5 inches? 63.5 mm
How many inches is 1.5 mm? 0.059 in (just under 1/16)
How many inches is 2 mm? 0.079 in (about 5/64)
How many inches is 20 mm? 0.787 in (about 25/32)
How many inches is 35 mm? 1.378 in (about 1 3/8)
How many inches is 40 mm? 1.575 in (about 1 37/64)
How many inches is 60 mm? 2.362 in (about 2 23/64)

How many mm in a cm, a foot and a meter?

The metric prefixes are powers of ten, so metric-to-metric conversion is just moving the decimal point. Imperial lengths convert through the exact 25.4 mm inch.

Unit Millimeters Inches
1 centimeter 10 mm 0.3937 in
1 inch 25.4 mm 1 in
1 foot 304.8 mm 12 in
1 yard 914.4 mm 36 in
1 meter 1000 mm 39.37 in (3 ft 3.37 in)

One millimeter is 0.1 cm, and 1 mm = 0.03937 in (1 ÷ 25.4). A “thou” or “mil” (0.001 in), used in machining and for plastic film thickness, is exactly 0.0254 mm (25.4 micrometers).

Converting feet and inches to mm (worked example)

A door listed as 6 ft 8 in tall:

  1. Convert everything to inches: 6 × 12 + 8 = 80 in.
  2. Multiply by 25.4: 80 × 25.4 = 2032 mm (203.2 cm).

Going the other way, 1500 mm ÷ 25.4 = 59.06 in. Take the whole feet out (59.06 ÷ 12 = 4 ft, remainder 11.06 in), so 1500 mm ≈ 4 ft 11 in.

Metric and imperial sizes that are close but not equal

Hardware often comes in near-equivalent sizes. They look interchangeable, but the gaps matter for wrenches, sockets and drill bits:

Metric Nearest inch size Inch size in mm Difference
6 mm 1/4 in 6.35 mm 0.35 mm
10 mm 3/8 in 9.525 mm 0.475 mm
13 mm 1/2 in 12.7 mm 0.3 mm
16 mm 5/8 in 15.875 mm 0.125 mm
19 mm 3/4 in 19.05 mm 0.05 mm
25 mm 1 in 25.4 mm 0.4 mm

A 19 mm socket and a 3/4 in socket are practically the same, while a 10 mm bolt in a 3/8 in hole is a loose fit. When the difference is under about 0.1 mm, most people can swap them; above that, use the correct system.

Measuring in mm and inches with your phone

  1. Open the ruler and calibrate it once with a credit card on the calibration page.
  2. Set the primary unit to mm and the secondary to inches, so both scales show at once.
  3. Lay the object on the screen with one end at zero and read the other end. No conversion needed.

A phone screen is only a few inches long, so for longer items, mark the screen edge, slide the object along and add the readings, or use a tape measure.

Sources

  • International yard and pound agreement (1959): 1 yd = 0.9144 m, so 1 in = 25.4 mm.
  • NIST, “The United States survey foot” (deprecated 31 December 2022).
  • NIST Special Publication 811, Guide for the Use of the International System of Units.