To read a ruler, line the object up with the 0 mark, find the last numbered mark before its end, then count the small lines after it. On a metric ruler, each small line is 1 millimeter (mm), and each number is 1 centimeter (cm), which is 10 mm. On an inch ruler, the smallest lines are usually 1/16 of an inch, and longer lines mark 1/8, 1/4 and 1/2 inch.

The rest of this guide explains each marking, with worked examples and a section on tape measures. You can follow along on an actual size online ruler on your phone.

The parts of a ruler

Before you read the numbers, it helps to know what you’re looking at:

  • Zero line. The starting point. On many rulers it’s a few millimeters in from the edge, so the end of the ruler is not zero.
  • Major graduations. The long, numbered lines: centimeters on the metric side, inches on the imperial side.
  • Minor graduations. The shorter lines in between: millimeters, or fractions of an inch.
  • Edges. A standard ruler has metric along one edge and inches along the other. The cm side usually counts to 15 (a 6-inch ruler) or 30 (a 12-inch ruler).

How to read mm on a ruler

The metric side is the easiest to read because everything counts in tens.

  • Numbered lines (1, 2, 3 …) are centimeters.
  • Small lines between them are millimeters. There are 10 spaces per centimeter.
  • The slightly longer line in the middle of each centimeter marks 5 mm, or half a centimeter.

Example: An object ends three small lines past the 4. That’s 4 cm + 3 mm = 43 mm, or 4.3 cm.

To read a ruler in mm, multiply the centimeter number by 10 and add the small lines. That’s why millimeters are the best unit for small things like screws, beads and jewelry.

Metric ruler cheat sheet

Line length Means Equals
Longest (numbered) 1 cm 10 mm
Medium 0.5 cm 5 mm
Shortest 0.1 cm 1 mm

Worked metric examples

Where the object ends Reading in mm Reading in cm
On the 7 70 mm 7.0 cm
2 small lines after 7 72 mm 7.2 cm
On the medium line after 12 125 mm 12.5 cm
8 small lines after 0 8 mm 0.8 cm
Halfway between the 3rd and 4th line after 9 ≈ 93.5 mm ≈ 9.35 cm

Reading half a millimeter. If the edge falls between two lines, you can estimate the half. That’s as precise as a plastic ruler gets. For anything finer, you need calipers.

How to read an inch ruler

Inch rulers split each inch into halves, quarters, eighths and sixteenths. The length of each line tells you which fraction it is.

Line length Fraction Decimal mm
Longest (numbered) 1 inch 1.0 25.4
Second longest 1/2 inch 0.5 12.7
Third 1/4 inch 0.25 6.35
Fourth 1/8 inch 0.125 3.175
Shortest 1/16 inch 0.0625 1.5875

Example: An object ends at the 2-inch mark plus 5 of the smallest lines. That’s 2 + 5/16 = 2 5/16 inches, or about 2.31 in.

Tip: Simplify fractions as you go. 8/16 is 1/2, 4/16 is 1/4 and 12/16 is 3/4. Ruler markings are drawn longer at these points to help you spot them.

Every sixteenth of an inch

Count the small lines from the last whole inch. This table gives the simplified name for each one.

Line after the whole inch Fraction Decimal Line Fraction Decimal
1 1/16 0.0625 9 9/16 0.5625
2 1/8 0.125 10 5/8 0.625
3 3/16 0.1875 11 11/16 0.6875
4 1/4 0.25 12 3/4 0.75
5 5/16 0.3125 13 13/16 0.8125
6 3/8 0.375 14 7/8 0.875
7 7/16 0.4375 15 15/16 0.9375
8 1/2 0.5 16 next whole inch 1.0

A faster way to count: don’t count all the way from the whole inch. Find the nearest long line (1/2 or 1/4) and count from there. For example, two small lines past the 3/4 mark is 12/16 + 2/16 = 14/16 = 7/8 in.

Rulers with 1/32 and decimal inches

  • 1/32-inch rulers (common on steel rules for machinists) have twice as many lines. Each small space is 1/32 in, about 0.79 mm. Use the same method and divide by 32.
  • Decimal-inch rulers divide each inch into 10 or 50 parts instead of fractions. On a tenths scale, each line is 0.1 in. Engineers use these because decimals add up more easily.

How to read a tape measure

A tape measure is an inch ruler on a roll, with a few extras:

  • Inch numbers and fractions work exactly as above. Most tapes mark 1/16 inch; some mark 1/32 for the first few inches.
  • Foot markers. Every 12 inches, the tape often shows “1F”, “2F” or a highlighted number, so 36 inches is labeled 3 feet.
  • Red numbers every 16 inches mark standard wall stud spacing in US building.
  • Small black diamonds every 19.2 inches mark truss and joist spacing (five per 8-foot sheet).
  • The hook at the end slides. It moves by its own thickness so that inside measurements (pushing against a wall) and outside measurements (hooking over an edge) are both correct. A loose hook is supposed to move, so don’t fix it in place.

Metric tapes work the same way, with centimeters numbered and millimeters between them. Many tapes print metric on one edge and inches on the other.

Converting between mm, cm and inches

  • 1 inch = 25.4 mm exactly
  • 1 cm = 0.3937 inches
  • 1 mm ≈ 1/25 inch

Quick check: a standard bank card is 85.60 mm long, which is 8.56 cm, or about 3 3/8 inches. If you have a card handy, it’s a good way to test any ruler, including an online one. See the full reference object size list, and the complete mm to inches chart for every fraction.

Step-by-step: measuring something properly

  1. Lay the object flat on a table, with the edge you’re measuring straight.
  2. Line up the 0 mark (not the ruler’s end) with one end of the object.
  3. Hold the ruler still with your other hand so it doesn’t slide.
  4. Look straight down at the far end of the object.
  5. Read the last numbered mark, then count the small lines past it.
  6. Write down the unit (mm, cm or in) so the number means something later.

Object longer than the ruler? Mark where the ruler ends with a pencil or your finger, move the ruler so its 0 sits on that mark, and add the readings. Each move adds a little error, so a tape measure is better for long things.

Damaged ruler end? Start at the 1 cm (or 1 inch) mark instead and subtract 1 from the reading. Carpenters call this “burning an inch.”

Reading an online ruler on your phone

A screen ruler is read exactly like a physical one, with one catch: it’s only actual size after calibration. Phone screens pack different numbers of pixels into each inch. An uncalibrated mm ruler at actual size on one phone can be several millimeters off on another, and the error grows with length.

On ruleronphone you calibrate once with a credit card, and the ticks then match real millimeters. The tool shows a primary and a secondary unit at the same time, so you can read mm and inches side by side without converting. The calibration page shows each step, and how to calibrate a ruler on screen compares the methods.

Tips for reading a screen ruler:

  • Put the object directly on the glass, with its end on the 0 line.
  • Keep browser zoom at 100%. Zooming changes the size of every tick.
  • Use the selection tool to measure width, height and diagonal at once instead of counting lines.

Common mistakes when reading a ruler

  1. Starting at the edge, not at zero. Many rulers have a small gap before the 0 line. Always line up with the 0 mark.
  2. Reading at an angle. Look straight down at the end of the object to avoid parallax error. On a thick ruler, this can be a millimeter or more.
  3. Mixing scales. On a dual ruler, make sure you count along the same side you started on.
  4. Miscounting sixteenths. Count from the nearest whole, half or quarter inch, not from zero.
  5. Counting lines instead of spaces. The first line is zero. You count the gaps after it.
  6. Forgetting the unit. “12” could be 12 mm, 12 cm or 12 inches, very different sizes.

How to read a ruler to the nearest 1/4, 1/8 or 1/16 inch

School worksheets and craft patterns often ask for a measurement “to the nearest 1/8 inch” or “to the nearest 1/4 inch”. That means you round to the closest line of that size, not that you ignore the smaller lines.

  1. Read the measurement to the smallest line you can see, usually 1/16 inch.
  2. Look at the nearest lines of the size you were asked for.
  3. Pick whichever one the edge is closer to. If it sits exactly halfway, the usual school convention is to round up.
Exact reading Nearest 1/16 Nearest 1/8 Nearest 1/4 Nearest 1/2
1 5/16 in 1 5/16 1 3/8 (rounded up from halfway) 1 1/4 1 1/2
2 3/16 in 2 3/16 2 1/4 (rounded up from halfway) 2 1/4 2
3 7/16 in 3 7/16 3 1/2 (rounded up from halfway) 3 1/2 3 1/2
4 11/16 in 4 11/16 4 3/4 (rounded up from halfway) 4 3/4 4 1/2

The same idea works in metric. “To the nearest centimeter” means 43 mm becomes 4 cm and 47 mm becomes 5 cm. “To the nearest millimeter” means you round your half-millimeter estimate to a whole line.

How accurate is a ruler?

A useful rule from measurement practice: you can reliably read a scale to about half of its smallest division. On a millimeter ruler that’s about ±0.5 mm; on a 1/16-inch ruler it’s about ±1/32 inch (0.8 mm). Your result can’t be more precise than that, so writing “43.27 mm” from a plastic ruler is false precision. Write 43 mm or 43.5 mm.

Other things limit accuracy as much as the markings do:

Source of error Typical effect How to reduce it
Parallax (reading at an angle) Up to a mm or more on thick rulers Look straight down; use a ruler with a thin, beveled edge
Worn or cut end Every reading is off by the missing amount Start from the 1 cm or 1 in line and subtract
Ruler not parallel to the object Reading is longer than the true length Align the ruler along the edge, not diagonally
Tape measure sag Long readings come out too long Support the tape or measure along a surface
Uncalibrated screen ruler Error grows with length Calibrate against a card first

If you need better than half a millimeter, use calipers or a micrometer. For tasks like hanging a picture, cutting fabric or checking a screw length, a ruler is more than enough.

How to read a metric tape measure

Metric tapes are read the same way as a centimeter ruler, but the numbers get large quickly. Most print every centimeter as a number, and the meter points are marked differently, often as “1m” or in red. So “1m 23” followed by 4 small lines reads as 1.234 m, which is 123.4 cm or 1,234 mm. Builders in metric countries usually quote everything in millimeters to avoid decimal points on drawings, so get used to reading “1234” directly.

On a dual tape with metric on one edge and inches on the other, choose one edge before you start and stay on it. A common mix-up is reading the inch number from the top edge and the fraction from the metric ticks on the bottom edge.

How to measure things that aren’t straight

  • Diameter of a circle (a coin, a pipe, a ring): place the 0 line on one edge and slide the ruler until you find the widest reading across. That’s the diameter. A reading anywhere other than through the center is too short.
  • Circumference (a wrist, a bottle, a finger): wrap a paper strip around it, mark where it overlaps, then lay the strip flat on the ruler. Paper doesn’t stretch the way string does. See the ring size guide for a worked example.
  • Curved lines on a map or pattern: lay a piece of string along the curve, mark the end, then straighten it on the ruler.
  • Inside of a box or drawer: a tape measure’s hook is designed for this. Push it against one side and add the length of the tape case if the tape’s body is printed with its size (for example “+3 in”).

Reading a ruler: three worked examples

Example 1 — a pencil. The pencil starts at 0 and ends 6 small lines past 17 on the metric edge. That’s 17 cm + 6 mm = 176 mm (17.6 cm). To convert, divide by 25.4: 176 ÷ 25.4 ≈ 6.93 in, which is just under 6 15/16 inches.

Example 2 — a picture frame opening. The opening ends 3 small lines past the 1/2-inch line after the 7. That’s 7 + 8/16 + 3/16 = 7 11/16 in. In millimeters: 7.6875 × 25.4 ≈ 195.3 mm.

Example 3 — a broken ruler. The ruler’s first centimeter is snapped off, so you line the object up with the 1 cm mark. The other end lands on 9.4 cm. The true length is 9.4 − 1 = 8.4 cm (84 mm).

Troubleshooting

  • The numbers on my ruler don’t start at zero. Some rulers print 0 a few millimeters in from the end, and some don’t print the 0 at all. The first long line is zero either way.
  • My two rulers disagree. Check both against a known object, like a bank card’s 85.60 mm edge. Cheap plastic rulers are usually fine, but printed paper rulers and screen rulers are often scaled wrong.
  • My online ruler is off by a few percent. That’s a pixel-density problem, not your reading. See why online rulers are inaccurate and recalibrate.
  • I can’t tell which line is 1/8 and which is 1/16. Find the longest unnumbered line first (1/2), then the next longest pair (1/4 and 3/4). Everything else follows from those.
  • No ruler at all? Use a known object instead. The guide to measuring without a ruler lists everyday items with exact sizes.

Practice: check yourself

Use a calibrated online ruler or a real one and measure these. The answers are the published sizes.

Object Expected answer
Long edge of a credit or ID card 85.6 mm (3 3/8 in)
US quarter, across 24.3 mm (about 15/16 in)
Euro €1 coin, across 23.3 mm
Short edge of an A4 sheet 210 mm (8 1/4 in)
Short edge of a US Letter sheet 215.9 mm (8 1/2 in)

If you’re within half a millimeter (or 1/32 inch), you’re reading the ruler correctly. Once you can read mm and sixteenths confidently, any ruler will be easy to use, whether it’s wood, steel, a tape measure or a calibrated online ruler.